Page 83

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Page 2 71 *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Mixing Nitocote EP500 is supplied in the correct proportions to facilitate easy on-site mixing. A slow speed electric drill with a suitable paddle can be used for efficient mixing. Satisfactory mixing can be achieved by thoroughly mixing all contents of the base resin and hardener component in the original container. Mix continuously for approximately 3 minutes until a uniform consistency has been reached. Application Nitocote EP500 is spray applied using specialised equipment and contractors are advised to carry out trials prior to proceeding with any contract. Advice on suitable application equipment and application method is available on request from your nearest Parchem sales office. To avoid sagging on overhead surfaces, do not apply Nitocote EP500 greater than 5 mm per layer. If a smooth surface is required, close the surface with a steel trowel. Note: do not thin components as solvents will prevent proper cure. Nitocote EP500 should be applied only when the substrate temperature and the ambient temperature is above 5°C. Do not attempt to mix part packs as incorrect proportioning can severely affect the cured properties of the product. Cleaning Nitocote EP500 should be removed from tools, equipment and mixers with Solvent 10 immediately after use. Limitations Nitocote EP500 should not be used when the temperature is below 5°C and falling. Do not mix part packs under any circumstances. The ambient and substrate temperatures will affect the spray application and product film build characteristics. If any doubts arise concerning temperature or substrate conditions, consult your local Parchem sales office. Estimating Supply 336688 Nitocote EP500 Base 16L PACK 336699 Nitocote EP500 Hardener 16L PACK 337744 Nitocote EP500 Base 200L 337755 Nitocote EP500 Hardener 138L Solvent 10: 4 and 20 litre cans Coverage Nitocote EP500: 8.0 m2/ 16 litre pack at 2 mm thick 3.2 m2/ 16 litre pack at 5 mm thick Notes: The coverage figures for Nitocote EP500 are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced. Storage Shelf life All products have a shelf life of 12 months at 20°C if kept in a dry store in the original, unopened packs. Storage conditions Store below 35°C in dry conditions in the original, unopened packs. Fosroc® Nitocote EP500


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above