CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. INDEX 566 Page 4 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Hydrotite Supply Profile Dimensions Metres per roll Metres per carton DSS0220 * 20 mm x 2 mm 25 100 CJ0725-3K * 25 mm x 7 mm 10 40 CJ1020-2K * 20 mm x 10 mm 10 50 CJ1030-4M 30 mm x 10 mm 10 40 CJ2020-M 20 mm x 20 mm 10 30 RSS 1208D 12 mm diameter 20 40 RSS161OD 16 mm diameter 10 20 RSS2014D 20 mm diameter 10 20 RSS2519D 25 MM diameter 5 10 * these profiles available with self adhesive backing Product Code 2200545 Hydrotite RSS2519D / LM 2200550 Hydrotite CJ0725-3K ADH / LM 2200551 Hydrotite CJ0720-2K-AD 2200555 Hydrotite CJ1020-2K ADH /LM 2200560 Hydrotite DSS0220 ADH BACK /LM 2200575 Hydrotite RSS 1208D /LM 2200580 Hydrotite RSS 1610D LM 2200595 Hydrotite RSS2205D LM 2200600 Hydrotite RSS 040P/LM Limitations Not recommended for use in suspended slabs or expansion joints Minimum of 50 mm cover of concrete over Hydrotite for reinforced concrete and 100 mm cover of concrete or unreinforced concrete based on concrete strength of 22.5N mm² Expansion rate can vary in salt or contaminated water Not for use where excessive shrinkage may occur Specification Clause Hydrophilic expanding waterstops shall be placed at the joints in the concrete at the locations shown on the drawings in accordance with the requirement of this specification. Waterstops where shown on drawings shall be Hydrotite (fill in profile number) Hydrophilic Waterstops as supplied by Parchem. The waterstop shall consist of a non-expansive chloroprene rubber, co-extruded with a blue hydrophilic rubber which is capable of swelling by approx. eight times by volume. The waterstop shall be treated with a delay coating to prevent premature expansion and be able to change colour upon expansion which acts as a visial alert that the waterstop has started to expand. The waterstop is to be installed strictly in accordance with the manufacturers recommendations. Please refer to Hydrotite Installation Guidelines.
Technical Dayta Sheet Compedium
To see the actual publication please follow the link above