Page 57

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Page 3 45 *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Cleaning Paveroc and Nitobond AR or Durafloor Level Prime should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically. Equipment used with Nitoprime Zincrich and Nitobond EP should be cleaned with Solvent 10. Limitations Paveroc should not be used when the temperature is below 10°C and falling. Do not mix part bags. The product should not be exposed to moving water during application. Exposure to heavy rainfall prior to the final set may result in surface scour. If any doubts arise concerning temperature or substrate conditions, consult your local Parchem branch. Supply 402080 Paveroc 20 kg Nitoprime Zincrich: 1 litre can Nitobond AR: 5 and 20 litre containers Durafloor Level Prime: 1, 5 and 20 litre containers Nitobond EP: 1.5 and 6 litre packs Solvent 10: 4 and 20 litre drums Coverage and yield Paveroc: Approximately 9.4 litres / 20 kg bag (0.63 m2 at 15 mm thickness) Nitoprime Zincrich: 7 m2 / litre (approx.) Nitobond AR: 6 - 8 m2 / litre Durafloor Level Prime: 6 - 8 m2 / litre Nitobond EP: 4 - 5 m2 / litre Note: the actual yield per bag of Paveroc will depend on the consistency used. The actual coverage rate of Nitobond AR will vary dependent on the texture and porosity of the substrate. The coverage figures for other products are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced. Specification Clause Refer to Parchem website for detailed specification clauses. (www.parchem.com.au) Storage Shelf life All products have a shelf life of 12 months if kept in a dry store in the original, unopened bags or packs. Storage conditions Store in dry conditions in the original, unopened bags or packs. If stored at high temperatures and/or high humidity conditions the shelf life may be reduced to 4 - 6 months. Nitobond AR should be protected from frost. Fosroc® Paveroc


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above