Page 519

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Page 2 507 Properties Product code: 742030 Form: Torch applied reinforced sheet Size: Roll width 1 m, length 7.5 m Thickness: Approx 5 mm when laid Reinforcement: Reinforced fibreglass mat Watertightness: 60 kPa (EN1928-B Method) Tensile strength: (EN 12311-1) - longitudinal 300 N/50 mm - transverse 200 N/50 mm Elongation (EN 12311-1): 2/2% Resistance to tearing: (EN 12310-1) 70/70 N Flow resistance at elevated temperature: (EN 1110) 20°C Application Instructions Surface preparation All surfaces to which Vapordiffuser is to be applied must be smooth, free from contaminants and loose material. Rough concrete to be “faired up” before commencing application. Contact your local Parchem branch for suitable fairing products from our extensive range. Priming Index Bitumen Primer should be applied to all prepared surfaces prior to application of membrane and allowed to dry. Primer will take at least one hour to dry at temperatures 25°C and above. At lower temperatures allow additional drying time. Index Bitumen Primer should be applied at rate of approx. 0.13 litres /m² to the surface to which Vapordiffuser will be applied. The coverage rate for the primer will vary depending on the porosity of the surface being treated. Primer may be applied by brush, roller or spray equipment, coverage must be uniform. Primed areas must be covered with the membrane on the same day. Application Vapordiffusor to be torch bonded to substrate along with the overlaps which are ready for bonding in the longitudinal direction of roll. Crosswise the membranes are abutted and not overlapped. When the membrane has been installed, a strip of smooth / plain membrane (Fidia or Argo P), at least 15 cm wide, should be bonded over traversal joints. Protection Vapordiffuser is not designed as a stand alone product, it must have an additional layer of membrane applied. If final membrane is exposed to UV, a mineral finish is required (such as Testudo Mineral or Fidia Mineral). Supply Vapordiffuser: Roll width 1 m, length 7.5 m Coverage Vapordiffuser: Approx 7m² per 7.5 m roll Product Code: 742030 Index Bitumen Primer: Product Code: 742105 8m²/litre Note: No allowance has been made for wastage. Storage Store in cool, dry conditions ie. not exceeding 25°C. Rolls must be stored on end and must not be stored lying down. Index® Vapordiffuser


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above