Page 480

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL broom etc. When applying renders, screeds, patch mortars etc over this slurry, optimum adhesion results are achieved as a “wet on wet’ application. When applied to surfaces as a slurry seal, this will perform as the system primer, enabling all Emerproof membranes to be applied over once dried. Emerproof Quick Dry Two Part can be applied over slurry primer while in wet state, offering big advantages on areas where conditions are damp, cold, humid and moist without delaying the application. Mix Designs A wide range of mix designs is achievable using Emer-Proof Multi Purpose Primer and WP Additive. Typical designs are detailed below: 1. General Screeds: Use Emer-Proof Multi Purpose Primer and WP Additive with water at 1:3 Ratio as mixing liquid for general screeds (as a starting guide only) 2. Patching and repair mortar: 50 kgs Ordinary Portland Cement 150 kgs grade C/M sharp sand 15 litres of Emer-Proof Multi Purpose Primer and WP Additive 2-3 litres (maximum) clean water Recommended thickness: 6 mm - 40 mm 3. Heavy-duty floor screed: 50 kgs Ordinary Portland Cement 75 kgs 3 to 6 mm granite chips 75 kgs grade C/M sharp sand 15 litres of Emer-Proof Multi Purpose Primer and WP Additive (no water addition, further addition of Emer-Proof Multi Purpose Primer and WP Additive can be used to wet product further). The screed should be of a semi-dry cohesive consistency. Recommended thickness: 10 mm - 40 mm 4. Render: 50 kgs Ordinary Portland Cement 150 kgs grade C/M sharp sand 2.5kg of lime maximum can be added to enhance anti-slump properties 15 litres Emer-Proof Multi Purpose Primer and WP Additive 1-2 litres of clean water. More can be added to adjust workability if required. The render should be of a semi-dry cohesive consistency. Recommended thickness: 6 mm - 9 mm 5. Bonding mortar for slip bricks, tiles, etc: 50 kgs Ordinary Portland Cement 125 kgs grade C/M sharp sand 15 litres Emer-Proof Multi Purpose Primer and WP Additive 1-2 litres of clean water. More can be added to adjust INDEX 468 workability if required. Water is adjusted to give a firm mortar. For fine joints, use grade M/B sand. Support where necessary until the mortar is set. Recommended thickness: 6 mm to 40 mm. 6. High bonding waterproof slurry coat: 20kg Portland cement 20kg grade C/M sharp sand 12 litres of Emer-Proof Multi Purpose Primer and WP Additive. To increase workability to a flowable/brushable consistency, increase addition of Emer-Proof Multi Purpose Primer and WP Additive until desired consistency is achieved. Cleaning With water while wet. Once dried Solvent 10 or light mechanical means may be required. Drying Times 30 mins @ 23oC Minimum double the drying time @ 10oC – apply membrane coatings only after primer has fully dried Please Note: Application of all liquid applied membranes and primers should always refer to the surface temperature conditions before commencing and not just ambient temperatures. (There are limitations to how hot/cold the surface temperature can be, when applying liquid based membrane or primer). For example: ambient temperatures may be 10°C but the substrate could be 0°C and have frost issues. The same applies with higher temperatures: ambient temperature may be 26°C but have a substrate temperature of 36°C Supply 743121 Emer-Proof Multi-Purpose Primer and WP Page 2 Additive 4L Pail (1L/6-8m² - as a primer) 743120 Emer-Proof Multi-Purpose Primer and WP Additive 15L Pail (1L/6-8m² - as a primer) Shelf life 12 months if kept in a cool, dry store. Storage Conditions Store in dry conditions at temperatures between 5°C and 30°C in the original, unopened containers. If stored at high temperatures, the shelf life may be reduced. Maintenance No special requirements, any damage identified during normal inspections should be repaired or replaced as appropriate. Emer-Proof® Multi Purpose Primer & WP Additive


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above