Page 475

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Technical Data Sheet Specification Clause Where required, all joints and pipe penetrations are to be waterproofed using a nitrile butadiene rubber flexible bond breaking tape with polyester carrier surface. The floor waste is to be waterproofed using a detailing collar consisting of a rear butyl rubber layer on a fleece fabric square. The tapes, pre-fabricated corners and squares are to be used with an Emer-Proof water based liquid applied membrane. The Emer-Proof Elastic Joint Band System from Parchem Construction Supplies meet the performance criteria and are approved products. Design Criteria The substrate must be suitably prepared, clean, sound, stable and free of protrusions in accordance with Parchem’s instructions. It must be primed according to the substrate with either, Emer-Proof Multi-Purpose Primer and Additive for porous and Emer-Proof Non-Porous Primer for non-porous substrates. The Emer-Proof Elastic Joint Band Tape, corners and accessories are installed first before the Emer-Proof water based liquid membranes. The Emer-Proof Elastic Joint Band Pipe Penetration Detailing Squares need a circular cut made in the centre at 60-70% of the pipes diameter before sliding in place over the pipe. All of the Emer-Proof Elastic Joint Band System accessories have a fleece that is designed to be embedded into the Emer-Proof water based liquid membranes which ensure full adhesion to the substrate for superior sealing in these critical areas. Step 1: Apply a liberal coat of one of the Emer-Proof ‘waterbased’ 463 Emer-Proof® Elastic Joint Band System Superior sealing system for critical joint areas over traditional bond-breaking sealants and tapes Uses The Emer-Proof Elastic Joint Band System has been developed as a superior alternative to traditional bond breaking methods for sealing critical movement zones. The Emer-Proof Elastic Joint Band System is suitable for internal, external underground and fully immersed applications. Advantages „ Can be used with ‘All’ Emer-Proof water based single or 2 part liquid membrane systems „ Superior sealing system for critical areas over traditional bond breaking sealants and tapes „ Suitable for sealing movement joints and small expansion joints up to 25mm „ Time efficient and simplified installation – no time wasted waiting for joint sealants to sufficiently skin and cure „ High elongation and movement capabilities - able to withstand movement in both longitudinal and lateral directions „ High density, high strength rubber composition with superior water, chemical and tear resistance „ Waterproof in their own right, which offers double protection when combined with an Emer-Proof water based liquid membrane over-laid „ System comes with pre-fabricated corners, pipe penetration detailing squares as well as a floor waste leak control flange butyl detailing collar for superior sealing in the most critical of areas Description The Emer-Proof Elastic Joint Band System is a combination of tape and detailing accessories designed and developed as a superior bond breaking alternative to traditional methods of sealing critical movement zones. Standards Compliance The Emer-Proof Elastic Joint Band System is an approved bond breaker, conforming to AS 3740 and is suitable for use in Class I, Class II and Class III membrane systems as per AS4858 and AS4654. Technical Support Parchem offers a comprehensive range of high performance, high quality waterproofing and construction products. In addition, Parchem offers a technical support package to specifiers, contractors and end-users, as well as on-site technical assistance. April 2014 Page 1 liquid applied membranes to internal and external corner intersections approximately 150mm wide. Step 2: Embed the Emer-Proof Elastic Joint Band Corners into the wet membrane, making sure full saturation of the fabric edges using a brush or spatula. Step 3: Measure and cut Emer-Proof Elastic Joint Band Tape for all wall / floor and wall / wall junctions. Ensure that the Emer-Proof Elastic Joint Band Tape is measured to allow for the minimum 50mm overlap onto the Emer-Proof Elastic Joint Band Corners. Step 4: As with the corners previously; Apply a liberal coat of the same liquid membrane to the surface of the wall / floor and/or wall / wall junction approximately 150mm. Step 5: Embed the pre-cut Emer-Proof Elastic Joint Band Tape into the wet membrane, ensuring full saturation of the fabric edges. Remove any air pockets, voids or creases that may have occurred during installation by way of brush or spatula. April 2014


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above