Page 467

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Emer-Proof® Extended Wear Clear Coat Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1800 624 322 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Page 2 455 Application Emer-Proof Extended Wear Clear Coat is applied to the cured Emer-Proof Top Coat by way of 6mm mohair roller sleeve or brush, in ‘thin’ coating applications. Application of 1-2 coats is recommended, dependant on likelihood and degree of potential stains and marks. Maintenence No special requirements, any damage identified during normal inspections should be repaired or replaced as appropriate. Limitations „ This product must be applied in ‘thin’ application coats. „ Not recommended over sand stone, limestone and similar surfaces. „ Do not apply coating when rain is forecast within the curing times. „ Not to be used for applications in immersed areas. „ Not to be used over wax residues, glass, fibreglass, chlorinated rubber, or epoxy coatings. „ Floor areas should have adequate falls. „ Base membrane must be thoroughly dry prior to Emer-Proof Extended Wear Clear Coat being applied. „ The Emer-Proof Top Coat should be left to dry for a minimum of 48 hours @ 23°C before the application of Emer-Proof Extended Wear Clear Coat takes place. Cleaning Water cleanup while in a wet state. Once dried removal by Solvent 10 or mechanical means. Drying times Tack free/re-coat time: 2-4 hours (will vary with surface porosity and temperatures experienced at time of application). Dry film: 8-12 hours; foot traffic – 24 hours: based on normal ambient conditions of 23°C. Allow a minimum further 24 hours of drying time @ 10°C. Please Note: Application of all liquid applied membranes and primers should always refer to the surface temperature conditions before commencing and not just ambient temperatures. (There are limitations to how hot/cold the surface temperature can be, when applying liquid based membrane or primer). For example: ambient temperatures may be 10°C but the substrate could be 0°C and have frost issues. The same applies with higher temperatures: ambient temperature may be 26°C but have a substrate temperature of 36°C. Supply 743119 Emer-Proof Extended Wear Clear Coat – 15L Pail (1L/8m²) 743118 Emer-Proof Top Coat (Grey) – 15L Pail Horizonal Application: (2 coats @ 1.5L per m² total) Vertical Application: (2 coats @ 1L per m² total) Shelf Life 12 months if kept in a cool, dry store. Storage Conditions Store in dry conditions at temperatures between 5°C and 30°C in the original, unopened containers. If stored at high temperatures, the shelf life may be reduced.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above