Page 458

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. INDEX 446 Page 3 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1800 624 322 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Drying times Recoat: 2-4 hours Dry film: 8-12 hours Flood testing: 7 days Resistance to ponding water: 7 days Tiling/toppings: 24 hours Based on normal ambient conditions of 23°C @ 50% RH Allow a further minimum 24 hours of drying time @ 10°C Please Note: Application of all liquid applied membranes and primers should always refer to the surface temperature conditions before commencing and not just ambient temperatures. (There are limitations to how hot/cold the surface temperature can be, when applying liquid based membranes or primers). For example: ambient temperatures may be 10°C but the substrate could be 0°C and have frost issues. The same applies with higher temperatures: ambient temperature may be 26°C but have a substrate temperature of 36°C Emer-Proof Tile Bond Flex polymer modified cement based tile adhesive is recommended for direct adhesion to the membrane. Emer-Proof Multi-Purpose Primer and Additive is recommended within screeds and renders directly over the membrane as a waterproof and adhesion enhancer. Cleaning Product while in a wet state will clean up with water. Once dried, product will need to be removed by Solvent 10 or by mechanical means. Splashes of Emer-Proof water based membrane on paintwork etc. should be wiped off immediately using a cloth dampened with a strong detergent solution. Brushes and brooms etc. should be soaked in a strong detergent solution immediately after application has finished. Hands and skin may be cleaned using a proprietary waterless hand cleaner, but prevention of soiling is better practice by wearing gloves and overalls. Supply 743116 Emer-Proof Under Tile – 15L Pail (1.5L/m²) 743124 Emer-Proof Non-Porous Primer – 1L Pail (1L/10m²) 743123 Emer-Proof Non-Porous Primer – 4L Pail (1L/10m²) 743121 Emer-Proof Multi-Purpose Primer and Additive 4L Pail (1L/6-8m²) 743120 Emer-Proof Multi-Purpose Primer and Additive 15 L Pail (1L/6-8m²) 743265 Emer-Proof Elastic Joint Band Tape 120mm W x 50M Roll 743270 Emer-Proof Elastic Joint Band Corner Internal 90o 135mm x 135mm – Each or 50/Box 743275 Emer-Proof Elastic Joint Band Corner External 270o 135mm x 135mm – Each or 50/Box 743125 Emer-Proof Elastic Joint Band Corner Adjustable Internal – 135mm x 135mm – Each or 50/Box 743126 Emer-Proof Pipe Detailing Square Small Each or 50/Box 743127 Emer-Proof Pipe Detailing Square Medium Each or 50/Box 743128 Emer-Proof Pipe Detailing Square Large Each or 50/Box 743129 Emer-Proof Butyl Square Floor Waste Detailing Collar – Each or 25/Box 405015 Emer-Proof Aquabarrier (Grey) – 20L Two Part Kit (1L/1.5m² per coat) Shelf life 12 months if kept in a cool, dry store. Storage conditions Store in dry conditions at temperatures between 5°C and 30°C in the original, unopened containers. If stored at high temperatures, the shelf life may be reduced. Emer-Proof® Under Tile


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above