Page 325

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Page 2 313 Emer-Seal® PU25 acting as a bond breaker. Priming requirements Good adhesion can be gained to clean, dry, uncontaminated concrete, timber, metals, ceramics, brickwork and most coating surfaces without the use of primers. On some surfaces however, adhesion may be improved by the use of a primer. Where doubt exists over the suitability of the substrate for unprimed adhesion, site trials should be conducted in conjunction with priming advice from Parchem. In most applications optimum adhesion to concrete and other porous materials can be achieved using Primer 21. Primer 13 must be used on concrete in applications subject to semi-permanent or long term water immersion. On nonporous materials such as aluminium, stainless steel and galvanised metals, Primer 4 or Primer 6 is recommended. Gun Loading Emer-Seal PU25 is applied using a suitable sealant gun. Insert the sachet into the gun, cut a slit in the top of the sachet, replace the end cap and apply the sealant. Application Extrude the sealant firmly into joint to ensure complete contact with joint faces. Smooth finish if necessary with a spatula wetted with a dilute detergent solution. Cleaning Clean tools immediately after use with Parchem Solvent. Limitations Do not apply Emer-Seal PU25 to bituminous surfaces or allow bitumen to contact Emer-Seal PU25. Paintability - although polyurethane sealants will generally accept painting with acrylic coatings, it is possible for plasticisers to migrate over time and stain the surface of the coating. Parchem recommends the use of Emer-Seal MS in these applications. Supply 600 ml foil sachet, cartons of 20. Product Code: 620525 Emer-Seal PU25 Conc. Grey 600ml (20/ctn) 620530 Emer-Seal PU25 White 600ml (20/ctn) 620535 Emer-Seal PU25 Sandstone 600ml (20/ctn) 620545 Emer-Seal PU25 Black 600ml (20/ctn) 620555 Emer-Seal PU25 Beige 600ml (20/ctn) 620560 Emer-Seal PU25 Driftwood 600ml(20/ctn) Coverage: On average one 600 ml sachet will supply 12 metres of 10mm Storage Shelf life 6 months. Store in a cool dry place.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above