Page 270

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. INDEX 258 Page 3 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Durafloor® N (Novolac) Mixing and Placing Clear Binder Using suitable measuring jugs and mixing vessel, add 1.5 litres of base resin to every 1.0 litre of hardener. Mix thoroughly for a min of 3 minutes using a slow speed mechanical stirrer and a suitable spiral epoxy mixing paddle. Note: If fillers and colour packs are to be added, initially mix clear binder for only 2 minutes. Clear coating Mix the required quantity as per Clear Binder instructions without the addition of colour packs or fillers. Apply first coat by brush or roller at 4-5m² per litre or slightly heavier if a slip-resistant grit is to be used. When using a slip resistant aggregate broadcast chosen aggregate onto the still tacky first coat at required rate. When the first coat is hard (typically next morning – refer Properties section) sweep off excess grit (if applicable) and re-coat in same manner. It is recommended to apply the second coat at right angles to the first. If a coloured finish is required, the use of coloured Durafloor HP as the first coat followed by a second coat of the Durafloor N clear coating should be considered. Trowel floor While continuing to mix 2.5 litres mixed binder (1.5 litre base + 1.0 litre hardener) add 12.5 litres Durafloor TF Fillers (by volume). If a colour finish is requested add 1 x 500 gram Durafloor colour pack of chosen colour at the start of this process. Once all the components have been added, continue to mix for a further two (2) minutes. Once mixed apply the Durafloor N trowel floor by spreading the material over the wet or tacky, not tack free, primed surface and compact to achieve a dense 5 mm seamless screed. Finish to a desired texture with a steel trowel and allow to cure. Self Smoothing floor While continuing to mix 10 litres of the clear binder (above) add 1 x 10 kg bag of the Durafloor SL fillers. If a colour finish is requested add 1 x 500 gram Durafloor colour pack of chosen colour. Once all the components have been added, continue to mix for a further 2 minutes. Once mixed, apply the Durafloor N self smoothing floor topping by pouring the mixed material onto the cured, tack free primed surface and spread with a steel trowel to achieve a 2 - 4 mm seamless topping. After allowing the screed material to set for approx 10-15 minutes, remove any air entrapment by a spike rolling and then allow to cure. Limitations Durafloor N should not be applied on to surfaces known to have rising damp or having a relative humidity reading greater than 80% (ie. moisture content greater than 5%). Durafloor N should be appplied only when the substrate temperature and the ambient temperature is above 10°C or when the ambient relative humidity is below 85% at the time of placement. Best performance life expectancy is enhanced by the use of sound housekeeping. The chemical resistance of Durafloor N is reduced slightly due to the addition of fillers and colour packs therefore when the maximum chemical resistance or stain resistance is required a finishing coat of Durafloor N Clear Coating should be considered. Supply Durafloor N (Novolac) Clear Binder: 401040 - Base: 15 litre pail 401045 - Hardener: 10 litre pail 405355 - Durafloor TF Fillers: 20 kg bag (12.5L) 412060 - Nitomortar F4 Fillers: 20 kg bag (13.5L) 404045 - Durafloor SL Fillers: 10 kg bag (8.0L) 610501 - Emer-Seal CR (Grey): 600 ml sausage The coverage figures given are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures may be reduced. Storage Durafloor N has a shelf life of 36 months if kept in a dry store in the original, unopened pack. Store in dry conditions between 5°C and 30°C away from sources of heat and naked flames, in the original, unopened packs. If stored at high temperatures the shelf life may be reduced.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above