CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Page 3 249 Durafloor® SL Estimating Supply Durafloor SL is supplied in packs containing pre-weighed components consisting of a base, hardener, colour pack/s and bag of fillers which, when combined produce 16 litres of mixed product. Durafloor SL 16L kit components: 405400 - 1 x Durafloor SL Base 16L kit 405700 - 1 x Durafloor SL Hardener 16L kit 404047 - 1 x Durafloor SL Fillers 14kg (standard filler quantity) OR 404045 - 1 x Durafloor SL Fillers 10kg (10kg Fillers only used when lower filler quantity required for specialised applications such as film studio floors, etc - please contact Parchem for further advice on these applications) 2 x Durafloor 0.5kg Colour Packs or 1 x Durafloor 1kg Colour Pack (See Durafloor Colour Chart for colour selection) Primer/Accessories: Nitomortar 903: 6 and 30 litre packs Solvent 10: 4 and 20 litre drums Coverage Durafloor SL: 16 litre pack (8m² @ 2 mm thickness/4m² @ 4 mm thickness) using 14kg SL Fillers Nitomortar 903: 5 m²/litre The coverage figures given are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced. Typically, an additional 10% should be allowed for surface irregularities and wastage although this will vary with site conditions. Specification Clause Flow-applied epoxy floor toppings The designated floor areas shall be surfaced with Durafloor SL, a 2-4 mm thick flow applied epoxy resin floor topping. The topping shall achieve a compressive strength of 90MPa and a flexural strength of 30 MPa at 7 days. At 23oC, it shall be capable of accepting foot traffic at 24 hours and vehicular traffic at 48 hours. Shelf life All products have a shelf life of 36 months if kept in a dry store in the original, unopened packs. Storage Conditions Store in dry conditions between 5°C and 30°C, away from sources of heat and naked flames, in the original, unopened packs. If stored at high temperatures the shelf life may be reduced.
Technical Dayta Sheet Compedium
To see the actual publication please follow the link above