Page 239

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Page 2 227 *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Fosroc® Nitoflor FC100 Coating Apply not less than two (2) coats of Nitoflor FC100 by short nap roller, brush or sprayer at a coverage rate of 6 - 8 m2/litre per coat. Parchem recommends the first coat be roller or brush applied or at least “back-rolled” to assist with the penetration into the concrete substrate. The coverage obtained will vary depending on the nature of the surface to be coated. Three (3) coats may be required on porous or coarse surfaces. One coat onto previously applied Concure CR may be acceptable. Site trial should be conducted to assess suitability. Ensure that it is completely and uniformly coated without thick or “ponded” areas which will adversely affect curing. Allow 2 - 4 hours between coats. Cleaning Nitoflor FC100 should be removed from tools and equipment with Solvent 10 immediately after use. Limitations Nitoflor FC100 should not be applied on to surfaces known to suffer from rising damp. The durability of Nitoflor FC100 in foot traffic areas is reduced in areas of very heavy traffic such as around work benches, drinks machines etc. It is advisable to either:- a. specify additional coats in such areas or, b. specify a higher build system such as Durafloor HP in such areas (see separate Technical Data Sheets) Nitoflor FC100 should not be applied at temperatures below 10°C or where ambient relative humidity exceeds 85%. Nitoflor FC100 should not be applied when the ambient temperature will exceed 30°C during application or within 24 hours after application, otherwise bubbling is liable to occur due to solvent entrapment. Nitoflor FC100 contain a significant level of flammable solvent which is expelled to the surrounding air during the drying process. Sufficient ventilation and the relevant OH&S precautions must be employed during and after application. Supply Nitoflor FC100 20 and 200 litre drums 410001 Nitoflor FC100 clear 200L 410002 Nitoflor FC100 clear 20L Coverage Nitoflor FC100 6 - 8 m²/L per coat Theoretical wet film thickness 125 - 165 (microns per coat): Theoretical dry film thickness (microns per coat): 28 - 33 Nitoflor FC100 is designed as a penetrating sealer therefore dry film thickness is not necessarily a true guide to what is achieved on-site. The coverage figures given are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced. Specification Clause Floor coating The floor coating shall be Nitoflor FC100, an acrylic based coating suitable for application by brush, roller or spray. The coating shall be applied in two coats at a coverage rate not greater than 6m²/litre per coat. Storage Shelf life Nitoflor FC100 has a shelf life of 36 months if kept at 25°C in a dry store in the original, unopened drums. Storage conditions Product contains highly flammable liquids therefore must be stored in flameproof areas in accordance with local regulations. Store well away from naked flames and sparks and all sources of heat. Store at ambient temperatures below 30°C. Keep container sealed when not in use.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above