Page 206

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. INDEX 194 Page 3 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Enamel / Oil Based: Depends on underlying substrate. For steel, abrade and apply Emer-Gard Primer Type 2. Other substrates refer to your local Parchem sales office. Timber surfaces: Treat previously painted surfaces as above. Prime: One coat of Emer-Acrylic Sealer. Note: do not apply Emer-Acrylic Sealer over old oil based paints. Powdery Paintwork or Absorbent Masonry Surfaces: Should be sealed with one coat of Emer-Coat Clear Sealer. Overcoating old Emer-Clad / Impact: Clean the surface with mild detergent, rinse with clean water, allow to dry. No primer required. If coatings are delaminating then remove all loose and flaky paint back to a sound firmly adhered edge then apply one coat of Emer-Coat Clear Sealer. Movement joints All expansion and movement joints should be sealed with a suitable sealant. Ideally, Emer-Impact should not be applied over movement joints as the amount of movement may be more than the capacity of the coating. Joints should be first sealed with the appropriate joint sealant then the Emer-Impact applied up to the edge of the joint. When this is not practical, all movement joints should be sealed with Emer-Seal MS. Polyurethane sealants should be avoided as they can bleed plasticisers into the coating above. Consult your local Parchem sales office for advice on the method best suited to your application. Application Emer-Impact may be applied by a variety of rollers to achieve a number of different texture finishes. Application by Rolana or long nap roller at 5 m²/litre/coat. Application by Roma or texture roller at 1.5 m²/litre/coat. Note: these figures may slightly vary depending on the substrate. Application on top of textured finishes including Emer-Impact Roma - 1 coat at 5 m²/litre. Spary Application When being applied to well prepared surfaces (no blow holes) it is possible to spray apply Emer-Impact in a single coat to achieve the 170 micron dry film thickness (360 micron wet film thickness). This can be a substantial time saving on a project. Suitable equipment includes Graco 795 or Graco 1095 airless running at 2800 psi and utilising 19 thou or 21 thou spray tips. For further information contact Parchem. To visually facilitate coverage and ensure adequate film build, different colours may be used for each coat of Emer-Impact. Note: do not apply any materials during damp or rainy conditions or where there is likelihood of rain. Temperatures above 30°C reduce the wet edge time and, as with other water based coatings, may increase the risk of showing lapmarks and rollermarks after drying, especially with darker colours. Dark colours may show slight oxidisation over time. This will not affect the performance of the coating. This can be removed temporarily by cleaning, Cleaning Tools and equipment should be cleaned with water immediately after use. Note: As with all specialty coatings we recommend that the application be carried out by an applicator who is skilled in the procedures and techniques necessary to achieve the desired finish. Supply Emer-Impact: 15 litre pail Emer-Acrylic Sealer: 1, 4 & 20 litre pails Emer-Proof Aqua Barrier: 20 litre kit Emer-Coat Clear Sealer: 1, 4 & 20 litre pails Emer-Patch (smooth): 15 litre pail Storage All products have a shelf life of 12 months if kept in a dry, cool storage area. Storage conditions Store in dry conditions at temperatures between 5°C and 30°C in the original, unopened containers. If stored at high temperatures, the shelf life may be reduced. Emer-Impact


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above