Page 20

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. INDEX 8 Page 4 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 repaired locations. The surrounding parts of the structure will generally benefit from the application of a protective barrier/ decorative coating to limit the advance of chlorides and carbon dioxide, thus bringing them up to the same protective standard as the repair itself. Parchem recommend the use of the Emer-Clad and Dekguard range of protective, anticarbonation coatings. These products provide a decorative and uniform appearance as well as protecting areas of the structure which might otherwise be at risk from the environment. Emer-Clad and Dekguard products may be applied over the repair area without prior removal of the Nitobond AR / Concure A99 curing membrane. Other curing membranes must be removed prior to the application of Emer-Clad and Dekguard products. Cleaning Nitobond HAR, Nitobond AR and Renderoc HB should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically. Equipment used with Nitoprime Zincrich and Nitobond EP should be cleaned with Solvent 10. Limitations Renderoc HB should not be used when the temperature is below 5°C and failing. Do not mix part bags. Due to the lightweight nature of Renderoc HB, the product should not be used in areas subjected to traffic. Neither should it be exposed to moving water during application. Exposure to heavy rainfall prior to the final set may result in surface scour. If any doubts arise concerning temperature or substrate conditions, consult your local Parchem sales office. NOTE: Renderoc HB is not designed to be used as a broad-scale building render. Estimating Supply Renderoc HB product code: 306095 Renderoc HB: 15 kg bag Nitoprime Zincrich: 1 litre can Nitobond HAR: 1, 5 and 20 litre containers Nitobond AR: 5 and 20 litre containers Nitobond EP: 1.5 and 6 litre packs Solvent 10: 4 and 20 litre cans Coverage and yield Renderoc HB: 12.1 - 12.5 litres/15 kg bag (approximately 1.25 at 10 mm thickness) Nitoprime Zincrich: 8 /litre Nitobond HAR: 3 - 4 /litre Nitobond AR: 6 - 8 /litre Nitobond EP: 4 - 5 /pack Note: the actual yield per bag of Renderoc HB will depend on the consistency used. The yield will be reduced if the material is applied by a spray technique. The coverage figures for liquid products are theoretical - due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced. Shelf life All products have a shelf life of 12 months if kept in a dry store in the original, unopened bags or packs. Storage conditions Store in dry conditions in original, unopened bags or packs. If stored at high temperatures and/or high humidity conditions the shelf life may be reduced to 4 to 6 months. Nitobond HAR and Nitobond AR to be protected from frost. Fosroc® Renderoc HB


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above