Page 166

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING ROOFING WATERSTOPS WATERPROOFING JOINT FILLERS TIMBER FLOORING ALPHABETICAL Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. INDEX 154 Page 3 *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Nitoprime DG should be applied at the same coverage rate as Dekguard Primer in continuous, multiple coats as necessary. If in doubt about the condition of the substrate, contact your local Parchem sales office. The primer should be allowed to dry for a minimum of two hours (at 20°C) before application of Dekguard S. Under no circumstances should the primer be overcoated until the surface is properly dry. Dekguard S may be applied by the use of suitable brushes, rollers or spray. For further information about application techniques, please consult your local Parchem sales office. All primed substrates should be treated with two coats of Dekguard S. The material should be stirred thoroughly before use. The first coat should be applied to all areas by the use of suitable brushes, rollers or spray to achieve a uniform coating with a wet film thickness not less than 175 microns. This coat should be allowed to dry before continuing. The second coat of Dekguard S should be applied exactly as detailed above, again achieving a wet film thickness not less than 175 microns. Cleaning Renderoc FC should be removed from tools and equipment with clean water immediately after use. Dekguard Primer, Nitoprime DG and Dekguard S should be removed from tools and equipment using Solvent 10. Limitations The Dekguard S system is formulated for application to clean, sound concrete or masonry. Where application over existing sound coatings or paints is required, trials should be conducted to ensure compatibility and retention of the bond between the underlying coating and the substrate. When applied over existing coatings or paints, the performance characteristics of Dekguard S may be impaired and its fire rating invalidated. Compatibility and soundness should be assessed on a trial area. For further advice consult your local Parchem sales office. Application should not commence if the temperature of the substrate is below 2°C. Estimating Supply Renderoc FC: 15 kg bag Dekguard Primer: 20 litre drum Nitoprime DG: 20 litre drum Dekguard S: 20 litre drum (PC: 561570) Solvent 10: 4 & 20 litre drum Coverage Renderoc FC: 9 litres (3.0 m² at 3 mm) Dekguard Primer: 2.5 m² per litre (total) Nitoprime DG: 2.5 m² per litre (total) Dekguard S: 3 m² per litre (total) The coverage figures given are theoretical - due to wastage factors, the variety and nature of possible substrates, practical coverage figures will be reduced. Storage Shelf life All products have a shelf life of 12 months if kept in a dry store in the original, unopened packs. Storage conditions Store in cool, dry conditions, away from sources of heat and naked flames, in the original, unopened packs. If stored at high temperatures and/or high humidity conditions the shelf life may be reduced. Fosroc® Dekguard S


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above