Page 151

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Page 2 139 *Manufactured and sold under license from Fosroc International Limited. Fosroc and the Fosroc logo are trade marks of Fosroc International Limited, used under license. *Denotes a trade mark of Fosroc International Limited. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Fosroc® Conbextra EP10 The storage handling and placement of the grout must be in strict accordance with the manufacturer’s instructions. Instructions for Use Foundation surface All contact surfaces must be free from oil, grease, free standing water or any loosely adherent material. Concrete surfaces should be cut back to a sound base. All dust must be removed and bolt holes or fixing pockets blown clean of any dirt or debris. Steel surfaces All steel surfaces should be shot blasted free of rust, paint and flaky mill scale. Formwork The formwork should be constructed to be leakproof as Conbextra EP10 is a free flowing grout. Loss of grout once the material is placed, but not hardened, will result in incomplete filling of the gap. For free flow grout conditions it is essential to provide a hydrostatic head of grout. To achieve this a feeding hopper system should be used. Forming materials should be coated with a release agent such as grease or wax material or a plastic coating. These coatings act as a bond breaker so that a smooth grout surface is achieved after form removal and the forms are protected for reuse. Mixing Pour all the contents of the hardener pack into the base container. Mix using a slow speed power mixer until homogeneous. For all products, mix using a slow speed power mixer for two minutes or until a uniform colour is achieved in the grout. Placing The mixed grout should be poured steadily from one side only to eliminate the entrapment of air. Continuous grout flow is essential. Sufficient grout must be available prior to starting. The time taken to pour a batch should be regulated to the time taken to prepare the next batch. With the smaller 300ml kit size a nozzle is provided so that when mixed can be squeezed or poured into small gaps or hairline cracks above 0.25mm. Please refer to the Conbextra Epoxy Grouts Application Guide for further information. This is available from the website or your local Parchem branch. Flow characteristics The maximum distance of flow is governed by the gap thickness, the head of grout applied and the ambient temperature. Cleaning All tools and equipment should be cleaned immediately after use with Parchem Solvent. Spillages should be absorbed with sand or sawdust and disposed in accordance with local regulations. Temperature During application Conbextra EP10 grouting may be carried out without special precautions at ambient temperatures from 5°C - 25°C. In service Conbextra EP10 is completely resistant to frost and sub zero teperatures. It is also suitable in service up to 45°C. Estimating Supply Conbextra EP10: 2 component packs 223115 Conbextra EP10 300ml Pack 223120 Conbextra EP10 1.5L Pack 223124 Conbextra EP10 Hardener 5L 223125 Conbextra EP10 Base 10L For further information on any of the above, please consult with your local Parchem sales office.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above