Page 103

Technical Dayta Sheet Compedium

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Important notice A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au ABN 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Page 3 91 Galvashield® CC Individual Connection Drill one rebar connection hole per unit location. Saw cut a groove approximately 6 mm wide by 12 mm deep into the concrete to interconnect the rebar connection hole and anode connection hole. *Please refer to the Galvashield CC Installation Guide for further details. Reinforcing steel connections should be made using the Rebar Connection Kit. Place the weighted end of the connector into the drilled hole until the steel coil contacts the reinforcing steel. Feed the steel connector wire through the Setting Tool and set into place by striking with a hammer. Connect the units directly to the rebar connection wire using the supplied wire connector. If installing in series, connect the units to the interconnecting cable with a wire connector (cable and wire connectors are available as the Anode Connection Kit). Verify continuity between unit locations and rebar connections with a multi-meter. A resistance of 1 ohm or less is acceptable. Drill holes as per the dimensions listed above to accommodate the anodes. Presoak the units for a minimum of 10 to a maximum of 20 minutes in a shallow water bath. Galvashield CC bedding mortar should be used to install the still wet units into presoaked (saturated-surface dry) holes. Place the mixed embedding mortar into the bottom 2/3 of each hole and slowly press in the unit allowing the mortar to fill the annular space ensuring there are no air voids between the unit and the parent concrete. The minimum unit cover depth shall be 20 mm. Place wires into grooves and top off unit holes and saw cuts flush to the concrete surface with embedding mortar. Embedding mortar should be wet cured or cured with a curing compound and protected from traffic for 24 hours. Precautions Galvashield CC units are not intended to address or repair structural damage. Where structural damage exists, consult a structural engineer. Galvashield CC anodes are designed to provide galvanic corrosion control. Corrosion control products significantly reduce or stop on-going corrosion. Concrete repairs should be completed using Galvashield XP units around the boundary of the patch prior to installing Galvashield CC units in the remaining unrepaired areas. For more information on corrosion mitigation strategies, contact Parchem. Packaging Galvashield CC units 20 units per box Galvashield CC bedding mortar 5kg bags, one bag per 20 units Rebar Connection kit 20 rebar connectors per box Anode Connection kit 15.2m insulation cable 25 wire connectors Setting Tool 1 unit per box Storage Store in dry conditions in the original unopened boxes. Avoid extremes of temperature and humidity. Units should be installed within one year. Health and Safety As with all cement-based materials, contact with moisture can release alkalis which may be harmful to exposed skin. Galvashield CC and Galvashield CC bedding mortar should be handled with suitable gloves and other personal protective equipment in accordance with standard procedures for handling cementitious materials. Mix left over water from the unit bath with cementitious material and dispose by normal means after hardening. Additional safety information is included in the Material Safety Data Sheet.


Technical Dayta Sheet Compedium
To see the actual publication please follow the link above