Page 499

32857 Parchem Technical Data Compendium 2015_Crop4emag.pdf

CONTENTS CONCRETE REPAIR CORROSION CONTROL GROUTS & ANCHORS PROTECTIVE COATINGS INDUSTRIAL FLOORING SURFACE TREATMENTS JOINT SEALANTS CONCRETE JOINTING JOINT FILLERS WATERPROOFING WATERSTOPS ROOFING TIMBER FLOORING ALPHABETICAL INDEX Technical Data Index® Fidia P and Mineral Sheet 487 Elastomeric, torch applied membrane, reinforced with rot-proof non-woven polyester and stabilised with glass mat Uses Fidia polyester is used as a continuous waterproofing membrane for foundations, basements, tunnels, roofs etc. Fidia Mineral may be used as the top layer in a two layer membrane system or as a single roof membrane for both new and renovation work. Advantages „ Index membranes have over 25 years of proven performance throughout Australia „ Specifically selected for Australian conditions „ Low VOC - 13 grams per Litre „ Handles ponding and permanently wet conditions „ No curing times. Instantly waterproof „ Uniform thickness - eliminating likelihood of uneven application possible with liquid applied membranes „ Polyester and glass fibre reinforcement ensure dimensional stability whilst allowing flexibility during application and service „ Excellent stability at both high and low temperatures „ High tear and impact resistance and excellent elasticity even at low temperatures „ Excellent elasticity even at low temperatures „ Upper face of membrane treated with serigraph talc providing a prepared surface for a reflective coating or acrylic paint film if required „ Available with either a plain or mineral finish Description Fidia is an elastoplastomeric torch applied bituminous sheet membrane reinforced with a non-woven spunbonded fabric and longitudinally stabilised with glass fibre strands. The bitumen compounds used to manufacture the product are modified with plastomers and elastomers which give the membrane excellent durability and stability at both high and low temperatures. The upper face is treated with serigraph talc, the lower face with a non-stick sacrificial polyethylene film called Flamina. The lower face is embossed with small squares which assist in the recognition of the correct melting temperature. The embossing also ensures good vapour diffusion in spot bonded or loose laid applications. Fidia Mineral has the upper face self protected with a layer of coloured ceramic granules. A 75 mm side selvedge is provided along one edge of the roll to allow for adequate heat welding of the side laps. Maintenance No special requirements, any damage identified during normal inspections should be repaired or replaced as appropriate. Properties Product Code: Plain: 742000 Mineral: 742004 Form: Torch applied reinforced sheet Size: Roll width 1 m, length 10 m Colour: Plain: Black Mineral: Grey Thickness: Plain: 3 mm Mineral: 4.5kg Reinforcement: Non-woven polyester fabric with glass fibres longitudinally Impermeability (EN1928): To water Tensile strength (UN12311-1): longitudinal 450 N/50 mm transverse 400 N/50 mm Ultimate elongation (EN12311-1): longitudinal 40% transverse 40% Cold flexibility (EN1109): -10oC Dimensional stability: Stable below 100°C Application temperature: 5°C - 45°C ambient Service temperature -10°C - 100°C (continuous ambient): Specification Clauses Where so designated on the drawing the surfaces shall be covered with a torch applied, reinforced, modified bituminous waterproofing membrane. The waterproofing will be built up using a base layer of 3 mm thick Index Fidia elastoplastomeric polymer bitumen membrane based on distilled bitumen blended with both plastomers and elastomers and reinforced with non-woven polyester fabric containing longitudinal glass fibre strands. The base layer waterproofing membrane must have been tested in accordance with UEAtc directive January 1984, and have a longitudinal and transverse tensile strength greater than 450 N/50 mm and 380 N/50 mm respectively, an ultimate L/T elongation in excess of 38% and flexibility at low temperature to -10°C. Application Instructions Surface preparation All surfaces to which Fidia is to be applied must be smooth, free from contaminants and loose material. Rough concrete to be “faired up” before commencing application. Contact your local Parchem branch for suitable fairing products from our extensive range. June 2014


32857 Parchem Technical Data Compendium 2015_Crop4emag.pdf
To see the actual publication please follow the link above